Decorate your environment! Live in colour!
First step: wall preparation
Prior to painting you should assess the condition of substrate and prepare the surface which you plan to decorate. If there are stains at home after water streaking, soot, nicotine or grease, then apply Śnieżka Zacieki Plamy paint which will cover them and protect against fungus growth. Any minor losses such as screw holes and cracks should be polished and then filled with Acryl PUTZ® LT 22 LIGHT repair compound. Ready to use mass makes it easier and quicker to prepare walls. Preferably apply it using a trowel or stainless steel float. If the wall requires more renovation, it is necessary to clean the ground and prime with proper ground primer. Then in the case of larger unevenness, apply Acryl PUTZ® ST10 START putty . For surfaces where only minor corrections are necessary, Acryl PUTZ® FS20 RACE putty can be applied.
Second step: preparation for colour changes
The most important is colour because it will transform the look of your room. If you are not convinced what shade to select, there are among others: brochures, colour palettes, test probes, testers as well as many other innovative tools such as virtual design wizards.
Before painting you should prepare place of work. Unwanted spots of paint are burdensome to wash, so it is a good idea to prevent them. Also remove all unnecessary items from walls – TV sets, lamps or paintings. Permanently attached cables, power supplies and decorations must be protected with foil and sealed with tape. It is also necessary to protect the floor. Tools which we need for painting are as follows: a roller, painting pole, painting cuvette and brush . - While selecting a roller you should follow the rule which says: the smoother ground, the shorter roller fleece - preferably of the length from 9 to 16 mm. Remember to wet a roller with water before using it and then centrifuge, which should provide optimal paint absorption - advises Krzysztof Kędzior, Chief Application and Training Specialist at Paints and Varnishes Factory Śnieżka SA.
By using a painting cuvette painting you can evenly put product on the roller. In order to maintain container clean, it is worth wrapping it with foil. After finishing work, you will be able to simply discard it. Then the only thing to do is to prime walls. It is best to coat them with high-quality priming emulsion, e.g. Śnieżka Grunt which levels out differences in texture and ground colour, aligning its absorption and increasing the efficiency of topcoats.
Step three: colour revolution
You have already chosen a colour and now you hold the painting tool in the palm of your hand. You are just a few roller flicks away from changing your interior. Start paint application from the top, that is from the ceiling. Then cover hard-to-reach places : around the windows, heaters, doors and corners. For such surfaces the most convenient will be a small paint brush or mini roller. Before attempting to paint walls, it is necessary to separate them from the ceiling with tape . In the case of larger planes, apply paint from the window to the interior of a room according to the direction of incidence of the light. Movements should be parallel, and indoor painting belts must overlap each other. When the first layer is dry, we can paint for the second time. However, this time in the opposite direction , so that we will cover any streaks.
It should also be pointed out that the paint application technique should follow the wet on wet rule. Take the paint liberally and evenly spread it across the wall in the direction top down, and then right left - so we get a uniform structure. - To achieve the best end result, strip off the painting tape fifteen minutes after painting, which allows you to obtain a straight line without the effect of scorch – advises the expert. To get the most of painting it is advisable to use high-quality paint products with a high opacity force and resistance to scrubbing. Emulsion latex paints Śnieżka Barwy Natury are characterised by high performance and colour durability. They also allow to "breathe walls". With Teflon® surface protector technology the coated surfaces are characterised by lower dirt particles attracting and dirt is less able to permanently bond with the substrate.
Following the above guidelines will facilitate and accelerate painting. Refurbished walls will give your house a new nature and recharge your rooms with colour freshness. Skills acquired in this way can be used to give your friends a heping hand with colour metamorphosis of their houses. After completed work you deserve , however, a relax with a refreshing cool drink cup. Then you will be able to admire in peace and quiet the end result of your work.